November 2020 ~ Ngoprek - Ngoprek Dunia Jaringan

Saturday, November 21, 2020

BELAJAR MPLS ( Multi protocol Label Swicth )

November 21, 2020 No comments

MPLS Backbone

Assalamualaikum temen - temen... kembali lagi di blogg saya dan terimakasih telah berkunjung di blogg sayaa... di blogg kali ini kita masih membahas materi di cisco ccnp yaaa, namun disini kita sudah masuk ke lab baru nih... yaitu MPLS ( Multi Protocol Layer Switch )..

Seperti biasa, karena ini adalah lab baru.. jadi saya akan membahas sedikit terlebih dahulu tentang mpls yaaa..

MPLS singkatan dari Multi Protocol Label Switching merupakan sebuah teknologi dalam sistem komunikasi berbasis IP yang efisien dan memudahkan manajemen trafik data, yaitu dengan cara mengirimkan data berdasarkan prioritas pada label data yang lewat, bukan berdasarkan IP Address, sehingga lebih terjamin kualitasnya. Teknologi MPLS merupakan penggabungan antara IP dan Asynchrounous Transfer Mode (ATM). MPLS mampu membentuk virtual circuit dalam network — nya

Metode MPLS adalah suatu metode forwarding data (meneruskan data) melalui suatu jaringan dengan menggunakan informasi dalam label yang dilekatkan pada paket IP. MPLS menggabungkan teknologi switching layer 2 dengan teknologi routing layer 3. MPLS melakukan enkapsulasi paket IP, dengan memasang header MPLS.

MPLS pada dasarnya terdiri dari 3 jenis router yaitu :

1. Router P (Provider)

Terdapat dalam MPLS Domain, P router terhubung dengan router-router lain yang dimiliki service provider
Pada jaringan MPLS yang tidak terlalu besar terkadang tidak terdapat P router didalamnya untuk menghemat biaya.

2. Router PE (Provider Edge)

Merupakan router yang terhubung langsung dengan router customer dan juga sekaligus dengan router service provider
Menjembatani antara network berbasis IP dengan network berbasis MPLS
Memberikan pelabelan pada paket IP yang masuk ke dalam MPLS Domain
Melepas pelabelan pada paket yang akan keluar dari MPLS Domain
PE Router ini sifatnya harus ada pada setiap jaringan MPLS

3. Router CE (Customer Edge)

Merupakan router yang terdapat di sisi customer
Pada router CE ini tidak terdapat konfigurasi MPLS apapun
Konfigurasi routing biasa, bisa static atau dynamic seperti OSPF / EIGRP

Oke kalo gitu kita langsumg ke konfigurasinya geysssss

TOPOLOGI =

R1#conf t

R1(config)#

R1(config)#ho PE-1

PE-1(config)#

PE-1(config)#int lo 0

PE-1(config-if)#ip add 10.10.10.1 255.255.255.255

PE-1(config-if)#

PE-1(config-if)#exit

PE-1(config)#

PE-1(config)#int g1/0

PE-1(config-if)#ip add 192.168.10.1 255.255.255.252

PE-1(config-if)#no sh

PE-1(config-if)#exit

PE-1(config)#

R2(config)#ho P

P(config)#int lo 0

P(config-if)#ip add 10.10.10.10 255.255.255.255

P(config-if)#

P(config-if)#int g1/0

P(config-if)#ip add 192.168.10.2 255.255.255.252

P(config-if)#no sh

P(config-if)#exit

P(config)#

P(config)#int g2/0

P(config-if)#ip add 192.168.20.1 255.255.255.252

P(config-if)#no sh

P(config-if)#

P(config-if)#exit

P(config)#

Sekarang kita coba test ping dulu!!!!....

PE1(config)#do ping 192.168.10.2

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.10.2, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 3/15/28 ms

P(config)#do ping 192.168.20.2

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.20.2, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 18/22/27 ms

PE-2#ping 192.168.20.1

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.20.1, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 20/24/31 ms

Oke sudah bisa yaaa, Selanjutnya kita buat dynamic routingnya... disini saya menggunakan dynamic routing ospf .... Kita kofigurasi routingnya di seluruh router yaa dan kita advertise ke area 0 saja

PE1(config)#rou

PE1(config)#router ospf 1

PE1(config-router)#net 192.168.10.1 0.0.0.0 area 0

PE1(config-router)#net 10.10.10.1 0.0.0.0 area 0

P(config)#router ospf 1

P(config-router)#net 192.168.10.2 0.0.0.0 area 0

P(config-router)#net 192.168.20.1 0.0.0.0 area 0

P(config-router)#net 10.10.10.10 0.0.0.0 area 0

P(config-router)#exit

PE2(config)#router ospf 1

PE2(config-router)#net 192.168.20.2 0.0.0.0 area 0

PE2(config-router)#net 10.10.10.2 0.0.0.0 area 0

Nahh kalo udah cek dulu di tabel routing setelah itu di ping yaaaa..........

PE1(config-router)#do sh ip route

192.168.10.0/30 is subnetted, 1 subnets

C 192.168.10.0 is directly connected, GigabitEthernet1/0

192.168.20.0/30 is subnetted, 1 subnets

O 192.168.20.0 [110/2] via 192.168.10.2, 00:23:14, GigabitEthernet1/0

10.0.0.0/32 is subnetted, 3 subnets

O 10.10.10.10 [110/2] via 192.168.10.2, 00:23:14, GigabitEthernet1/0

O 10.10.10.2 [110/3] via 192.168.10.2, 00:09:00, GigabitEthernet1/0

C 10.10.10.1 is directly connected, Loopback0

P(config)#do sh ip rou

192.168.10.0/30 is subnetted, 1 subnets

C 192.168.10.0 is directly connected, GigabitEthernet1/0

192.168.20.0/30 is subnetted, 1 subnets

C 192.168.20.0 is directly connected, GigabitEthernet2/0

10.0.0.0/32 is subnetted, 3 subnets

C 10.10.10.10 is directly connected, Loopback0

O 10.10.10.2 [110/2] via 192.168.20.2, 00:06:20, GigabitEthernet2/0

O 10.10.10.1 [110/2] via 192.168.10.1, 00:23:11, GigabitEthernet1/0

PE2#show ip route

192.168.10.0/30 is subnetted, 1 subnets

O 192.168.10.0 [110/2] via 192.168.20.1, 00:17:40, GigabitEthernet1/0

192.168.20.0/30 is subnetted, 1 subnets

C 192.168.20.0 is directly connected, GigabitEthernet1/0

10.0.0.0/32 is subnetted, 3 subnets

O 10.10.10.10 [110/2] via 192.168.20.1, 00:17:40, GigabitEthernet1/0

C 10.10.10.2 is directly connected, Loopback0

O 10.10.10.1 [110/3] via 192.168.20.1, 00:17:40, GigabitEthernet1/0

PE1(config)#do ping 10.10.10.1

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.10.10.1, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 4/11/20 ms

P(config)#do ping 10.10.10.2

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.10.10.2, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 20/26/31 ms

PE-2#ping 10.10.10.10

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.10.10.10, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 17/20/34 ms

Sekarang kita konfigurasi MPLS nya, sebenarnya sangat mudah dalam mengkonfigurasi mpls di router cisco....

PE1(config)#mpls ip

PE1(config)#int g1/0

PE1(config-if)#mpls ip

PE1(config-if)#exit

P(config)#mpls ip

P(config)#int g1/0

P(config-if)#mpls ip

P(config-if)#int g2/0

P(config-if)#mpls ip

PE2(config)#mpls ip

PE2(config)#int g1/0

PE2(config-if)#mpls ip

Setelah dikonfigurasi, untuk pengecekan apakah MPLS sudah aktif dan berjalan dengan baik, gunakan perintah berikut ini.....

PE1(config)#do sh mpls forwarding

Local Outgoing Prefix Bytes Label Outgoing Next Hop

Label Label or VC or Tunnel Id Switched interface

16 17 10.10.10.2/32 0 Gi1/0 192.168.10.2

17 Pop Label 10.10.10.10/32 0 Gi1/0 192.168.10.2

18 Pop Label 192.168.20.0/30 0 Gi1/0 192.168.10.2

P(config)#do sh mpls forwarding

Local Outgoing Prefix Bytes Label Outgoing Next Hop

Label Label or VC or Tunnel Id Switched interface

16 Pop Label 10.10.10.1/32 762 Gi1/0 192.168.10.1

17 Pop Label 10.10.10.2/32 1016 Gi2/0 192.168.20.2

PE2(config)#do sh mpls forwarding

Local Outgoing Prefix Bytes Label Outgoing Next Hop

Label Label or VC or Tunnel Id Switched interface

16 16 10.10.10.1/32 0 Gi1/0 192.168.20.1

17 Pop Label 10.10.10.10/32 0 Gi1/0 192.168.20.1

18 Pop Label 192.168.10.0/30 0 Gi1/0 192.168.20.1

DONE :)

TERIMAKASIH

WASSALAMU'ALAIAKUM WR.WB

BELAJAR VPN ( Phase 3 Dynamic Mapping With OSPF )

November 13, 2020 No comments

Phase 3 Dynamic Mapping With OSPF

Assalamualaikum temen - temen, selamat datang di blogg saya... dan terimakasih telah berkesempatan mengunjungi blogg saya, Di blogg kali ini kita masih akan membahas mengenai materi yang ada di bab VPN yaaaa tentunya masih di pembahasan Cisco CCNP...

Sesuai judul, kalian pasti udah tau lah yaa kita mau bahas apa pada blogg kali ini??... yaaa bener banget!!, kali ini kita akan membahas tentang Phase 3 Dynmaic Mapping With OSPF..Sebenernya lab ini dengan lab sebelumnya hanya ada sedikit perbedaan ya... yaitu berbeda di dynamic routing protocolnya... karena di lab sebelumnya menggunakan routing EIGRP, nah sekarang kita akan pake routing OSPF..

Dan tujuan dari lab ini sama saja dengan lab sebelumnya... yang berbeda cuman di segi routing nya.... dan sedikit di bagian konfigurasinya..

Karena ini adalah lab lanjutan... soooo saya hanya melakukan konfigurasi yang hanya pada lab ini saja yaa.., jadi jika temen - temenn ingin melihat konfigurasi dasarnya bisa dilihat di blog saya sebelumnya atau kalo mau cepet bisa di cek link dibawah...

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-gre-tunnel.html

BELAJAR VPN ( GRE TUNNEL ) - Lab 1 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-ipsec-tunnel-mode.html

BELAJAR VPN ( IPSEC Tunnel Mode ) - Lab 2 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-bgp-dmvpn.html

BELAJAR VPN ( DMVPN ) - Lab 3 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-1-dynamic-mapping.html

BELAJAR VPN ( Phase 1 Dynamic Mapping With EIGRP ) - Lab 4 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-1-dynamic-mapping_9.html

BELAJAR VPN ( Phase 1 Dynamic Mapping With OSPF ) - Lab 5 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-1-with-ipsec.html

BELAJAR VPN ( Phase 1 With IPsec )

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-2-dynamic-mapping.html

BELAJAR VPN ( Phase 2 Dynamic Mapping )

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-2-dynamic-mapping_10.html

BELAJAR VPN ( Phase 2 Dynamic Mapping With EIGRP )

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-2-dynamic-mapping_11.html

BELAJAR VPN ( Phase 2 Dynamic Mapping With OSPF )

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-3-dynamic-mapping.html

BELAJAR VPN ( Phase 3 Dynamic Mapping )

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-3-dynamic-mapping_12.html

BELAJAR VPN ( Phase 3 Dynamic Mapping With EIGRP )

TOPOLOGI

Sebelum kita mulai konfigurasi intinya... kita hapus terlebih dahulu konfigurasi sebelumnya, yaitu konfigurasi routing EIGRP

Kalo sudah... langsung kita ke konfigurasinyaaaaa.....

HUB(config)#rou

HUB(config)#router ospf 12

HUB(config-router)#net 1.1.1.1 0.0.0.0 area 0

HUB(config-router)#net 192.168.10.0 0.0.0.255 area 0

HUB(config-router)#

HUB(config-router)#exit

HUB(config)#

HUB(config)#int tu 0

HUB(config-if)#ip ospf network broa

HUB(config-if)#ip ospf network broadcast

HUB(config-if)#ex

Spoke-1(config)#

Spoke-1(config)#router ospf 12

Spoke-1(config-router)#net 2.2.2.2 0.0.0.0 area 0

Spoke-1(config-router)#net 192.168.10.0 0.0.0.255 area 0

Spoke-1(config-router)#

Spoke-1(config-router)#exit

Spoke-1(config)#

Spoke-1(config)#int tu 0

Spoke-1(config-if)#ip ospf netw

Spoke-1(config-if)#ip ospf network broad

Spoke-1(config-if)#ip ospf network broadcast

Spoke-1(config-if)#ex

Spoke-1(config)#

Spoke-2(config)#route

Spoke-2(config)#router ospf 12

Spoke-2(config-router)#

Spoke-2(config-router)#net

Spoke-2(config-router)#network 192.168.10.0 0.0.0.255 area 0

Spoke-2(config-router)#net 3.3.3.3 0.0.0.0 area 0

Spoke-2(config-router)#exit

Spoke-2(config)#

Spoke-2(config)#int tu 0

Spoke-2(config-if)#ip ospf network broadcast

Spoke-2(config-if)#ex

Spoke-2(config)#

Terakhir... kita tinggal cek!!!!...

HUB(config)#do sh ip rou ospf

2.0.0.0/32 is subnetted, 1 subnets

O 2.2.2.2 [110/1001] via 192.168.10.2, 00:02:05, Tunnel0

3.0.0.0/32 is subnetted, 1 subnets

O 3.3.3.3 [110/1001] via 192.168.10.3, 00:02:17, Tunnel0

Spoke-1(config)#do sh ip route ospf

1.0.0.0/32 is subnetted, 1 subnets

O 1.1.1.1 [110/1001] via 192.168.10.1, 00:07:04, Tunnel0

3.0.0.0/32 is subnetted, 1 subnets

O 3.3.3.3 [110/1001] via 192.168.10.3, 00:05:32, Tunnel0

Spoke-2(config)#do ping 192.168.10.2

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.10.2, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 44/69/81 ms

HUB(config)#do ping 192.168.10.3

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.10.3, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 37/50/74 ms

DONE😊😊😊😊

TERIMAKASIH

WASSALAMUALAIKUM WR.WB

BELAJAR VPN ( Phase 3 Dynamic Mapping With EIGRP )

November 13, 2020 No comments

Phase 3 Dynamic Mapping With EIGRP

Sesuai judul, kalian pasti udah tau lah yaa kita mau bahas apa pada blogg kali ini??... yaaa bener banget!!, kali ini kita akan membahas tentang Phase 3 Dynmaic Mapping With EIGRP.. Sebenarnya tidak ada perbedaan dengan lab sebelumnya...tujuan nya tetap samaaa, namun disini kita akan mengkombinasikan menggunakan dynamic routing protocol EIGRP

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-gre-tunnel.html

BELAJAR VPN ( GRE TUNNEL ) - Lab 1 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-ipsec-tunnel-mode.html

BELAJAR VPN ( IPSEC Tunnel Mode ) - Lab 2 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-bgp-dmvpn.html

BELAJAR VPN ( DMVPN ) - Lab 3 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-1-dynamic-mapping.html

BELAJAR VPN ( Phase 1 Dynamic Mapping With EIGRP ) - Lab 4 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-1-dynamic-mapping_9.html

BELAJAR VPN ( Phase 1 Dynamic Mapping With OSPF ) - Lab 5 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-1-with-ipsec.html

BELAJAR VPN ( Phase 1 With IPsec )

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-2-dynamic-mapping.html

BELAJAR VPN ( Phase 2 Dynamic Mapping )

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-2-dynamic-mapping_10.html

BELAJAR VPN ( Phase 2 Dynamic Mapping With EIGRP )

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-2-dynamic-mapping_11.html

BELAJAR VPN ( Phase 2 Dynamic Mapping With OSPF )

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-3-dynamic-mapping.html

BELAJAR VPN ( Phase 3 Dynamic Mapping )

Oke... langsung aja kita ke konfigurasinya gess

TOPOLOGI =

HUB(config)#rou eig 12

HUB(config-router)#net 1.1.1.1 0.0.0.0

HUB(config-router)#net 192.168.10.1 0.0.0.0

HUB(config-router)#no aut

HUB(config-router)#no auto-summary

HUB(config-router)#

HUB(config-router)#exit

HUB(config)#

HUB(config)#int tu 0

HUB(config-if)#no ip split-ho

HUB(config-if)#no ip split-horizon eigrp 12

HUB(config-if)#ex

Spoke-1(config)#route

Spoke-1(config)#router eigrp 12

Spoke-1(config-router)#net 2.2.2.2 0.0.0.0

Spoke-1(config-router)#net 192.168.10.2 0.0.0.0

Spoke-1(config-router)#no aut

Spoke-1(config-router)#no auto-summary

Spoke-1(config-router)#exit

Spoke-2(config)#

Spoke-2(config)#route

Spoke-2(config)#router eigrp 12

Spoke-2(config-router)#

Spoke-2(config-router)#net 3.3.3.3 0.0.0.0

Spoke-2(config-router)#net 192.168.10.3 0.0.0.0

Spoke-2(config-router)#

Spoke-2(config-router)#no aut

Spoke-2(config-router)#no auto-summary

Sekarang tinggal kita CEK!!!......

Spoke-1(config)#do sh ip route eigrp

1.0.0.0/32 is subnetted, 1 subnets

D 1.1.1.1 [90/27008000] via 192.168.10.1, 00:42:12, Tunnel0

3.0.0.0/32 is subnetted, 1 subnets

D 3.3.3.3 [90/28288000] via 192.168.10.1, 00:45:44, Tunnel0

HUB(config)#do sh ip route eigrp

2.0.0.0/32 is subnetted, 1 subnets

D 2.2.2.2 [90/22248000] via 192.168.10.2, 00:30:25, Tunnel0

3.0.0.0/32 is subnetted, 1 subnets

D 3.3.3.3 [90/28218000] via 192.168.10.3, 00:37:01, Tunnel0

DONE😊😊😊

TERIMAKASIH

WASSALAMUALAIKUM WR.WB

BELAJAR VPN ( Phase 3 Dynamic Mapping )

November 13, 2020 No comments

Phase 3 Dynamic Mapping

Assalamualaikum temen - temen, kembali lagi di blogg saya.. dan terimakasih telah berkesempatan mengunjungi blogg saya... Di blogg kali ini kita masih membahas masih seputar VPN yaaaa dan lebih tepatnya yaitu yang sudah tertera di judul Phase 3 Dynamic Mapping...

Sebenernya tidak begitu jauh perbedaan nya dengan Phase 2, namun disini kita hanya menambah konfigurasi redirect dan shorcut.

Karena ini adalah lab lanjutan dari sebelumnyaaa... sooo disini saya hanya melakukan konfigurasi yang hanya pada lab ini yaa, dan jika temen - temen ingin melihat konfigurasi sebelumnya atau konfigurasi dasar dari lab ini.. temen - temen bisa lihat di link yang ada dibawah ini...

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-gre-tunnel.html

BELAJAR VPN ( GRE TUNNEL ) - Lab 1 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-ipsec-tunnel-mode.html

BELAJAR VPN ( IPSEC Tunnel Mode ) - Lab 2 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-bgp-dmvpn.html

BELAJAR VPN ( DMVPN ) - Lab 3 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-1-dynamic-mapping.html

BELAJAR VPN ( Phase 1 Dynamic Mapping With EIGRP ) - Lab 4 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-1-dynamic-mapping_9.html

BELAJAR VPN ( Phase 1 Dynamic Mapping With OSPF ) - Lab 5 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-1-with-ipsec.html

BELAJAR VPN ( Phase 1 With IPsec )

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-2-dynamic-mapping.html

BELAJAR VPN ( Phase 2 Dynamic Mapping )

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-2-dynamic-mapping_10.html

BELAJAR VPN ( Phase 2 Dynamic Mapping With EIGRP )

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-2-dynamic-mapping_11.html

BELAJAR VPN ( Phase 2 Dynamic Mapping With OSPF )

Oke?? langsung aja kita ke konfigurasinyaaa 😊😊😊

TOPOLOGI

HUB#conf t

Configuring from terminal, memory, or network [terminal]? Enter configuration commands, one per line. End with CNTL/Z

HUB(config)#

HUB(config)#int tu 0

HUB(config-if)#

HUB(config-if)#ip nhrp redi

HUB(config-if)#ip nhrp redirect

HUB(config-if)#ex

HUB(config)#

Spoke-1(config)#

Spoke-1(config)#int tu 0

Spoke-1(config-if)#ip nhrp red

Spoke-1(config-if)#ip nhrp redirect

Spoke-1(config-if)#

Spoke-1(config-if)#ex

Spoke-1(config)#

Spoke-2(config)#int tu 0

Spoke-2(config-if)#ip nhrp red

Spoke-2(config-if)#

Spoke-2(config-if)#exit

Langkah selanjutnya tinggal pengecekkan!!!!!...

HUB(config)#do sh dmvpn

Legend: Attrb --> S - Static, D - Dynamic, I - Incomplete

N - NATed, L - Local, X - No Socket

# Ent --> Number of NHRP entries with same NBMA peer

NHS Status: E --> Expecting Replies, R --> Responding, W --> Waiting

==============================================================

Interface: Tunnel0, IPv4 NHRP Details

Type:Hub, NHRP Peers:2,

# Ent Peer NBMA Addr Peer Tunnel Add State UpDn Tm Attrb

----- --------------- --------------- ----- -------- -----

1 23.23.23.1..........................192.168.10.2 UP 00:45:14 D

1 24.24.24.1 192.168.10.3 UP 00:44:25 D

HUB(config)#do ping 192.168.10.2

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.10.2, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max =49/57/66 ms

HUB(config)#do ping 192.168.10.3

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.10.3, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 30/62/75 ms

Spoke-1(config)#do ping 192.168.10.1

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.10.1, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 37/54/68 ms

Spoke-2(config)#do ping 192.168.10.2

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 192.168.10.2, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 41/76/80 ms

DONE😊😊😊😊

TERIMAKASIH

WASSALAMUALAIKUM WR.WB

BELAJAR VPN ( Phase 2 Dynamic Mapping With OSPF )

November 12, 2020 No comments

Phase 2 Dynamic Mapping With OSPF

Sesuai judul, kalian pasti udah tau lah yaa kita mau bahas apa pada blogg kali ini??... yaaa bener banget!!, kali ini kita akan membahas tentang Phase 2 Dynmaic Mapping With OSPF..Sebenernya lab ini dengan lab sebelumnya hanya ada sedikit perbedaan ya... yaitu berbeda di dynamic routing protocolnya... karena di lab sebelumnya menggunakan routing EIGRP, nah sekarang kita akan pake routing OSPF..

Dan tujuan dari lab ini sama saja dengan lab sebelumnya... yang berbeda cuman di segi routing nya.... dan sedikit di bagian konfigurasinya..

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-gre-tunnel.html

BELAJAR VPN ( GRE TUNNEL ) - Lab 1 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-ipsec-tunnel-mode.html

BELAJAR VPN ( IPSEC Tunnel Mode ) - Lab 2 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-bgp-dmvpn.html

BELAJAR VPN ( DMVPN ) - Lab 3 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-1-dynamic-mapping.html

BELAJAR VPN ( Phase 1 Dynamic Mapping With EIGRP ) - Lab 4 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-1-dynamic-mapping_9.html

BELAJAR VPN ( Phase 1 Dynamic Mapping With OSPF ) - Lab 5 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-1-with-ipsec.html

BELAJAR VPN ( Phase 1 With IPsec )

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-2-dynamic-mapping.html

BELAJAR VPN ( Phase 2 Dynamic Mapping )

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-2-dynamic-mapping_10.html

BELAJAR VPN ( Phase 2 Dynamic Mapping With EIGRP )

Oke tanpa berlama - lama lagi kita langsung aja ke konfigurasinya geasssss

TOPOLOGI =

Sebelum melakukan konfigurasi... kita hapus dulu konfigurasi sebelumnya yaitu hanya konfiguras routing EIGRPnya saja... di router HUB dan SPOKE...

kalo udah... langsung kita ke konfigurasi nya ges....

HUB(config)#rou

HUB(config)#router ospf 12

HUB(config-router)#net 1.1.1.1 0.0.0.0 area 0

HUB(config-router)#net 192.168.10.0 0.0.0.255 area 0

HUB(config-router)#exit

HUB(config)#

HUB(config)#int tu 0

HUB(config-if)#ip ospf net broad

HUB(config-if)#ex

Spoke-1(config)#

Spoke-1(config)#route

Spoke-1(config)#router ospf 12

Spoke-1(config-router)#net 2.2.2.2 0.0.0.0 area 0

Spoke-1(config-router)#net 192.168.10.0 0.0.0.255 area 0

Spoke-1(config-router)#exit

Spoke-1(config-router)#

Spoke-1(config)#int tu 0

Spoke-1(config-if)#

Spoke-1(config-if)#ip ospf netw broadcas

Spoke-1(config-if)#exit

Spoke-1(config)#

Spoke-2(config)#router ospf 12

Spoke-2(config-router)#net 192.168.10.0 0.0.0.255 area 0

Spoke-2(config-router)#net 3.3.3.3 0.0.0.0 area 0

Spoke-2(config-router)#exit

Spoke-2(config)#

Spoke-2(config)#int tu 0

Spoke-2(config-if)#ip ospf netw

Spoke-2(config-if)#ip ospf network broa

Spoke-2(config-if)#ip ospf network broadcast

Spoke-2(config-if)#

Langkah Terakhir kita tes PING!!!!!, Kita cukup ping ke loopbacknya saja

HUB(config)#do ping 2.2.2.2

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 47/55/72 ms

Spoke-1(config)#do ping 1.1.1.1

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 30/41/56 ms

Spoke-2(config)#do ping 2.2.2.2

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 2.2.2.2, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 39/45/60 ms

DONE😊😊😊😊

TERIMAKASIH

WASSALAMUALAIKUM WR.WB

BELAJAR VPN ( Phase 2 Dynamic Mapping With EIGRP )

November 11, 2020 No comments

Phase 2 Dynamic Mapping With EIGRP

Assalamualaikum temen - temen.. kembali lagi di blogg saya, dan terimakasih telah berkunjung di blogg saya, pada kali ini kita masih membahas bab mengenai VPN yaaa dan lebih tepatnya adalah Phase 2 Dynamic Mapping With EIGRP... sebenarnya disini sama saja dengan lab sebelumnya... hanya saja disini kita menggunakan routing EIGRP...

Karena ini adalah lab lanjutan jadi saya hanya melakukan konfigurasi yang hanya ada pada lab ini saja, jika temen - temen ingin melihat konfigurasi sebelumnya ato konfigurasi dasarnya... bisa dilihat di link dibawah =

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-gre-tunnel.html

BELAJAR VPN ( GRE TUNNEL ) - Lab 1 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-ipsec-tunnel-mode.html

BELAJAR VPN ( IPSEC Tunnel Mode ) - Lab 2 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-bgp-dmvpn.html

BELAJAR VPN ( DMVPN ) - Lab 3 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-1-dynamic-mapping.html

BELAJAR VPN ( Phase 1 Dynamic Mapping With EIGRP ) - Lab 4 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-1-dynamic-mapping_9.html

BELAJAR VPN ( Phase 1 Dynamic Mapping With OSPF ) - Lab 5 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-1-with-ipsec.html

BELAJAR VPN ( Phase 1 With IPsec )

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-2-dynamic-mapping.html

BELAJAR VPN ( Phase 2 Dynamic Mapping )

Oke... tanpa basa - basi lagi langsung kita cuss ke konfigurasinyaaa

TOPOLOGI =

HUB#

HUB(config)#rou

HUB(config)#router eigrp 12

HUB(config-router)#net

HUB(config-router)#network 1.1.1.1 0.0.0.0

HUB(config-router)#net 192.168.10.1 0.0.0.0

HUB(config-router)#no au

HUB(config-router)#no auto-summary

HUB(config-router)#exit

HUB(config)#

Spoke-1(config)#ro

Spoke-1(config)#router eigrp 12

Spoke-1(config-router)#net 2.2.2.2 0.0.0.0

Spoke-1(config-router)#net 192.168.10.2 0.0.0.0

Spoke-1(config-router)#no au

Spoke-1(config-router)#no auto-summary

Spoke-2(config)#rout eig 12

Spoke-2(config-router)#net 3.3.3.3 0.0.0.0

Spoke-2(config-router)#net 192.168.10.3 0.0.0.0

Spoke-2(config-router)#no auto-sum

Spoke-2(config-router)#exit

Spoke-2(config)#

Sekarang kita lakukan pengecekkan!!!!!.....

HUB(config)#do sh ip eigrp neigh eigrp

IPv4 Neighbors for AS(12)

HAddress Interface Hold Uptime SRTT RTO Q Seq

(sec) (ms) Cnt Num

1 192.168.10.3 Tu0 12 00:05:13 82 1434 0 3

0 192.168.10.2 Tu0 14 00:05:87 64 1434 0 4

HUB(config)#show ip route eigrp

Gateway of last resort is 12.12.12.2 to network 0.0.0.0

2.0.0.0/32 is subnetted, 1 subnets

D 2.2.2.2 [90/27008000] via 192.168.10.2, 00:18:49, Tunnel0

3.0.0.0/32 is subnetted, 1 subnets

D 3.3.3.3 [90/27008000] via 192.168.10.3, 00:18:31, Tunnel0

Spoke-1(config)#do sh ip route eigrp

1.0.0.0/32 is subnetted, 1 subnets

D 1.1.1.1 [90/27008000] via 192.168.10.1, 00:22:14, Tunnel0

Spoke-2#show ip route eigrp

1.0.0.0/32 is subnetted, 1 subnets

D 1.1.1.1 [90/27008000] via 192.168.10.1, 00:27:05, Tunnel0

Dapat dilihat bahwa routing table eigrp masih belum lengkap. hal ini terjadi adanya split horizon karena routing protocol distance vector defaultnya menerapkan split horizon dimana router tidak akan mengadvertise network di dalam interface yang sama. Maka itu kita perlu disable kan split horizon nya.....

HUB(config)#int tu 0

HUB(config-if)#no ip split-

HUB(config-if)#no ip split-horizon eig 12

Spoke-1#sh ip route eigrp

1.0.0.0/32 is subnetted, 1 subnets

D 1.1.1.1 [90/27008000] via 192.168.10.1, 00:33:14, Tunnel0

3.0.0.0/32 is subnetted, 1 subnets

D 3.3.3.3 [90/28288000] via 192.168.10.1, 00:00:07, Tunnel0

Spoke-2

Spoke-2#show ip route eigrp

1.0.0.0/32 is subnetted, 1 subnets

D 1.1.1.1 [90/27008000] via 192.168.10.1, 00:39:22, Tunnel0

2.0.0.0/32 is subnetted, 1 subnets

D 2.2.2.2 [90/28288000] via 192.168.10.1, 00:17:31, Tunnel0

TEST PING........

Spoke-1(config)#do ping 3.3.3.3

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 3.3.3.3, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 30/58/83 ms

DONE!!!!😊😊😊

TERIMAKASIH

WASSALAMUALAIKUM WR.WB

BELAJAR VPN ( Phase 2 Dynamic Mapping )

November 10, 2020 No comments

Phase 2 Dynamic Mapping

Assalamualaikum temen - temen, kembali lagi di blogg saya... dan terimakasih telah berkesempatan mengunjungi blogg saya. Pada blogg kali ini saya akan kembali membahas lab di Cisco CCNP yaa.. lebih tepatnya di bab VPN

Namun disini kita masuk ke bab Phase 2 Dynamic Mapping, karena di lab sebelumnya kita masih membahas Phase 1 Dynamic mapping..

Karena ini adalah lab lanjutan dari sebelumnya, jadi saya hanya melakukan konfigurasi yang hanya pada lab ini saja.. kalo temen - temen ingin melihat konfigurasi sebelumnya.. temen - temen bisa lihat dari link dibawah :

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-gre-tunnel.html

BELAJAR VPN ( GRE TUNNEL ) - Lab 1 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-ipsec-tunnel-mode.html

BELAJAR VPN ( IPSEC Tunnel Mode ) - Lab 2 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-bgp-dmvpn.html

BELAJAR VPN ( DMVPN ) - Lab 3 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-1-dynamic-mapping.html

BELAJAR VPN ( Phase 1 Dynamic Mapping With EIGRP ) - Lab 4 VPN

👉https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-1-dynamic-mapping_9.html

BELAJAR VPN ( Phase 1 Dynamic Mapping With OSPF ) - Lab 5 VPN

https://insinyurbocah2109.blogspot.com/2020/11/belajar-vpn-phase-1-with-ipsec.html

BELAJAR VPN ( Phase 1 With IPsec )

Soo kita langsung ke konfigurasinya...

TOPOLOGI =

Sebelum melakukan konfigurasi nya... kita hapus dulu konfigurasi tunnel dan routingnya, Jika sudah, langsung aja ke konfigurasinyaa.....

HUB(config)#int tu 0

HUB(config-if)#ip add 192.168.10.1 255.255.255.0

HUB(config-if)#

HUB(config-if)#tun mode gre multi

HUB(config-if)#tun sou 12.12.12.1

HUB(config-if)#

HUB(config-if)#ip nhrp network-id 1

HUB(config-if)#ip nhrp authen

HUB(config-if)#ip nhrp authentication IDN

HUB(config-if)#ip nhrp map multicast dynamic

HUB(config-if)#

HUB(config-if)#ex

HUB(config)#

Spoke-1(config)#int tu 0

Spoke-1(config-if)#ip add 192.168.10.2 255.255.255.0

Spoke-1(config-if)#

Spoke-1(config-if)#tu mod gre mult

Spoke-1(config-if)#tu sour 23.23.23.1

Spoke-1(config-if)#

Spoke-1(config-if)#ip nhrp network-id 1

Spoke-1(config-if)#ip nhrp authen

Spoke-1(config-if)#ip nhrp authentication IDN

Spoke-1(config-if)#ip nhrp map 192.168.10.1 12.12.12.1

Spoke-1(config-if)#

Spoke-1(config-if)#ip nhrp nhs 192.168.10.1

Spoke-1(config-if)#ip nhrp map mult

Spoke-1(config-if)#ip nhrp map multicast 12.12.12.1

Spoke-1(config-if)#exit

Spoke-1(config)#

Spoke-2(config)#int tu 0

Spoke-2(config-if)#

Spoke-2(config-if)#ip add 192.168.10.3 255.255.255.0

Spoke-2(config-if)#tu mod gre multipo

Spoke-2(config-if)#tun sou 24.24.24.1

Spoke-2(config-if)#

Spoke-2(config-if)#ip nhrp network-id 1

Spoke-2(config-if)#ip nhrp authent

Spoke-2(config-if)#ip nhrp authentication IDN

Spoke-2(config-if)#

Spoke-2(config-if)#ip nhrp map 192.168.10.1 12.12.12.1

Spoke-2(config-if)#ip nhrp nhs 192.168.10.1

Spoke-2(config-if)#ip nhrp map multicast 12.12.12.1

Spoke-2(config-if)#exit

Spoke-2(config)#

Terakhir kita tinggal pengecekkan.......

HUB(config)#do sh dmvpn

Legend: Attrb --> S - Static, D - Dynamic, I - Incomplete

N - NATed, L - Local, X - No Socket

# Ent --> Number of NHRP entries with same NBMA peer

NHS Status: E --> Expecting Replies, R --> Responding, W --> Waiting

UpDn Time --> Up or Down Time for a Tunnel

Interface: Tunnel0, IPv4 NHRP Details

Type:Hub, NHRP Peers:2,

# Ent Peer NBMA Addr Peer Tunnel Add State UpDn Tm Attrb

----- --------------- --------------- ----- -------- -----

1 23.23.23.1..........................192.168.10.2 UP 00:26:05 D

1 24.24.24.1 192.168.10.3 UP 00:23:50 D

HUB#show ip nhrp

192.168.10.2/32 via 192.168.10.2

Tunnel0 created 00:26:09, expire 01:33:50

Type: dynamic, Flags: unique registered used

NBMA address: 23.23.23.1

192.168.10.3/32 via 192.168.10.3

Tunnel0 created 00:23:54, expire 01:36:05

Type: dynamic, Flags: unique registered used

NBMA address: 24.24.24.1

HUB(config)#do show ip nhrp brief

Target Via NBMA Mode Intfc Claimed

192.168.10.2/32 192.168.10.2 .................... 23.23.23.1 dynamic Tu0 < >

192.168.10.3/32 192.168.10.3 24.24.24.1 dynamic Tu0 < >

DONE....😊😊😊😊

TERIMAKASIH

WASSALAMUALAIKUM WR.WB

Ngoprek - Ngoprek Dunia Jaringan

Cara Melihat Versi Mikrotik

EBGP Peering

Dasar - Dasar Firewall

Network Automation

Video Tutorial Jaringan

Saturday, November 21, 2020

BELAJAR MPLS ( Multi protocol Label Swicth )

Friday, November 13, 2020

BELAJAR VPN ( Phase 3 Dynamic Mapping With OSPF )

BELAJAR VPN ( Phase 3 Dynamic Mapping With EIGRP )

BELAJAR VPN ( Phase 3 Dynamic Mapping )

Thursday, November 12, 2020

BELAJAR VPN ( Phase 2 Dynamic Mapping With OSPF )

Wednesday, November 11, 2020

BELAJAR VPN ( Phase 2 Dynamic Mapping With EIGRP )

Tuesday, November 10, 2020

BELAJAR VPN ( Phase 2 Dynamic Mapping )

cari materi

Tentang Saya

Statistik Pengunjung

Blog Archive

Terjemahkan Blog Ini

Postingan Terbaru

ISIS Dynamic Route with Juniper

Saturday, November 21, 2020

Friday, November 13, 2020

Thursday, November 12, 2020

Wednesday, November 11, 2020

Tuesday, November 10, 2020

FOLLOW KITA YUK

cari materi

Tentang Saya

Statistik Pengunjung

Blog Archive

Terjemahkan Blog Ini

Postingan Terbaru